2005 SRX FUEL FILTER
2005 Cadillac SRX Replacement Fuel Filters – CARiD
wwwd››Fuel Filters & Parts›Cadillac›SRXHarmful impurities in fuel can plug injectors and reduce performance in your 2005 Cadillac SRX. Trap them before they can inflict damage with our replacement fuel filter.
SOLVED: 2005 cadillac v6 srx fuel filter location - Fixya
wwwa››Cadillac›SRX›2005 Cadillac SRX2005 cadillac v6 srx fuel filter location how to change fuel filter on 2005 cadillac v6 srx - Cadillac 2005 SRX questionHi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US. Here's a link to this great service Good luck!Locate the drain plug, size 13mm, drain the oil, replace drain plug. The oil filter is located by the dipstick. Replace filter put 5 of 5w-30 synthetic and you are good to go. and the oil filter is located to the right of the engine cover if your looking in at it. It looks like a small cast iron canister with a nut on top (its all molded together). unscrew the top of that and it is in there, the oil wrench come and can adjust to different size, I assume you never done an oil change and don't have any tools. go to any local auto parts store and tell them you need everything from oil,filter,removal tools, oil pan, funnel and they will give you everything you need ans some advice. when you put the filter back on, I would only do hand tighten . make sure you rub a bit of oil around the new rubber seal on your new filter using your figure . Buy the time you spend for all the tools what what need for oil change you will spend as much as having the pro do it, Oil change has been cheaper to change now day compair doing it your self. many places are offering 19 to 29 oil change, its worth all the hassle to let them do it. do the math, filter 6, 6qt of oil 27, tools 8, funnel 3, oil pan 12 right there is 56 buck plus you get to craw under the car and get dirty.0Directly under the engine. You'll see a large smooth portion under there that looks like the underside of a bath tub and on the lowest portion of that is a bolt. Thats your oil reservoir where you drain your oil. The filter should be located near that pointing toward the front of the vehicle. GM OEM filters are usually black but could be white and are almost always 3" filters so a filter wrench that fits a 3" filter will get it off without problem.0First you have to take out the one and only screw in the rear hatch door - it's where the hand pull down is you use to close the hatch. Then you have to pop all the plastic clips all the way around the plastic door panel, trying not to pull them out from the frame . If you do pull out the white plastic plugs from the frame you better make certain you take them off the plastic housing and insert them back into their frame holes - or you will never get the housing back on. Once you have the housing loose disconnect the inside tail gate light wire to remove the whole thing. Then you have to remove 7 to 8 nuts from the back of entire License plate, back up bulb housing using a deep socket to get in there. Work it loose from the rear of the car and it will come out just enough to work on the lights. This is tricky since the screw mounts don't give you much room to work with. Once you have the license plate and back up bulb frame loose you will see the two housings for the license plate bulbs on top. Slide out the license plate bulb lens and twist the bulb connection to remove the bulbs. Replace both of them - you don't want to do this again in a month when the other one blows. OPTIONAL: Once you take out the bulbs you might see that the housing is melted where the bulb wanted to burn through. Drill two small holes one is each end of the housing before I put everything back together to release some of the heat. Reverse the whole process to put everything back together. It's not easy. Make sure you insert the cables through the opening for the hatch handle or it will kink and not work properly. The bulbs come in a two pack of cost $4 .0If you go to the auto parts store they should have a fuel line disconnect tool that has a 5/16ths end an a 3/8ths end. The tool is shaped like an X. Before you start you need to pull the fuel pump fuse under the front of the REAR passenger side seat while the car is running and let it stall. it will release the built up pressure. This is important unless you want gas to spray every where. Then take the tool and start with the end of the filter with two lines. Place the appropriate end of the tool over the smallest inlet, push the tool in then pull the line towards the filter and then push the line away and it should disconnect. Do the same with line above. Then you can use the two appropriate size wrenches to disconnect the outlet end. reconnecting the new filter is simple just make sure your quick connect lines click in all the way and you tighten the outlet line well, I think its like 22 or 25 ft/lbs.0Right bank is 1,3,5 left bank is 2,4,6 this helps luck.0Located in fuel tank0